TEREX TC50 COMPACT EXCAVATOR
Terex has introduced the TC50 compact crawler excavator, designed for work in space-restricted areas.
• Offering a stable, zero-tail swing platform, the TC50 excels in 
constricted work environments, according to the manufacturer. It is designed to turn within its tracks, guaranteeing that the rear of the machine does not swing into nearby structures or landscaping or into oncoming traffic during operation.
• In addition, the offset boom allows for working in close proximity next to buildings and foundations.
• It is powered by a 39.4 hp Yanmar 4TNV88 engine and load-sensing and load-independent flow division hydraulics system that are matched to the machine’s size.
• It weighs 11,067 pounds and offers a maximum reach of 20 feet, 4 inches.
• The optional quick-attach coupler system allows for easy bucket and attachment change.
• The TC50 is able to handle 2.5 to 13.2 cubic-foot bucket capacities and can also use a hydraulic hammer.
Visit www.terex.com for more information.
MORBARK TYPHOON 20 CHIPPER
The Typhoon 20 brush chipper offers a 20-inch capacity.
• The machine has a drum and feed wheel both 28 ½ inches wide, and the six knife pockets allow three full cuts per revolution, which increases chipping efficiency.
• The Typhoon is available with 250 or 235 horsepower options.
• It is equipped with a 4-inch by 8-inch center beam and a 66 ½ -inch by 
40 ½ -inch infeed shoot, designed so the chipper can accept a wider variety of materials and be fed with auxiliary loading equipment.
• The machine also has a redesigned pivot, which eliminates the yoke swing and increases down pressure efficiently, according to the manufacturer.
• The unit comes with a 2 ½-inch lunet ring, 20,000-pound tandem axle suspension along with heavy-duty 3/8-inch chains and clasp hooks to secure the Typhoon 20 for efficient towing.
Visit www.morbark.com or call (800) 831-0042 for more information.
TRAMAC DEMOLITION CRUSHER AND SHEARS
Ingersoll Rand Tramac crushers and shears are designed for use on medium
and large sized excavators.
• The single attachment with interchangeable jaws maximizes versatility and cost efficiency.
• The RB jaw design simultaneously cuts steel and crushes concrete.
• Several jaw models feature removable and field replaceable cutting blades allow for easy maintenance and maximum productivity.
Visit www.ingersollrand.com for more information.
CATERPILLAR AP655D ASPHALT PAVER
The AP655D can be used in a wide range of applications from routine commercial jobs to demanding highway operations.
• Typical applications for the AP655D include: highways, urban and rural streets, county roads, lane additions, industrial sites, overlays, airport runways and other medium-to high-production paving jobs.
• The machine is powered by a Cat C6.6 engine with ACERT Technology that is U.S. EPA Tier 3 emission compliant. It also features dual operating stations with the Advisor Monitoring System (AMS), tilting consoles, 
exclusive Mobil-trac undercarriage or steel track undercarriage, high capacity cooling system, belt or hydraulic driven generator system and Caterpillar’s unique material handling system with independent auger and conveyor controls.
• Optional features include friction steering, smooth Mobil-trac belt, power folding front hopper apron and a track plow.
• The Cat C6.6 engine is a 6-cylinder that provides 174 hp.
• The machine can also be purchased with a steel track undercarriage.
Visit www.cat.com for more information.
GRASAN CUSTOM-BUILT CRUSHING PLANT
Grasan has introduced a primary track-mounted crushing plant designed to meet specifications for high-production aggregate applications. 
• Plants can be custom designed depending on the customer’s requirements, according to the manufacturer.
• The plant shown here uses a Hazemag 1515 APPH primary horizontal impact crusher with fully automatic hydraulic cylinder system for increased production capacity.
• The crusher inlet hood is made of extra heavy-duty steel plate with dual chain curtains.
Visit www.grasan.com for more information.
POWERSCREEN CHIEFTAIN 1700
The new Powerscreen Chieftain 1700 has been added to the globally successful Chieftain Range. The 1700 has been developed as a highly mobile two and three deck model giving up the six product separation. This model has been specifically designed to fit into the mid range bracket 
between Chieftain 1400 and 2100.
• Can be set up in less than 30 minutes.
• Has an adjustable high amplitude two bearing screen action, which can expose material to varying amplitudes and G force, helping separate material into the various required specifications.
• Hydraulic Screen Angle adjustment varies the material-travel rate over the screen deck to achieve the cleanest product in the most difficult applications.
• Four integral hydraulically folding stockpile conveyors fold and transport with the machine, removing the need for assisted lifting devices to put the machine in a working mode.
• Full access walkways give access to three sides of the screen for ease of maintenance and screen mesh change.
• A transverse power-unit giving greater access to the engine compartment for east of maintenance.
Visit www.powerscreen.com, call (502) 736-5200 or e-mail info@terexcs.com for more information.
PETERSON 5710C HORIZONTAL GRINDER
The 5710C is powered by a Caterpillar C27 1,050-hp engine and provides the highest power-to-weight ratio of any Peterson grinder.
• At 82,330 pounds, the 5710C was designed for operations requiring high production and frequent moves between jobs.
• With a feed opening of 60 inches by 44 inches and Peterson’s high lift feed roll, the 5710C is designed to handle a wide range of material, 
including stumps.
• The 5710C uses Peterson’s new generation of Impact Release System, which can be set in the detent mode to provide consistent product sizing or switched to the floating anvil mode for a primary reduction where accurate sizing is less critical. The floating anvil mode provides a high production primary reduction with more protection from contaminated feedstocks and reduced fuel consumption.
• The 5710C has a square-shaft rotor and large grate area that enables it to produce materials to exact specifications, according to a press release from the manufacturer.
• The quick-change multiple grate system is designed to make it easy to customize grate configurations to produce a wide variety of finished materials. Grates are removed through an access door on the side wall.
Visit www.petersoncorp.com for more information.
AIM SCORPION HYDRAULIC HAMMERS
Scorpion Hydraulic Hammers from AIM Attachments are designed for use with skid steers, backhoes and excavators of all sizes. 
• Scorpion Hammers are designed for the toughest jobs and have a compact design.
• The hammers have a boltless mounting system, designed for lower maintenance.
• In addition, the line features vibrosilencing to reduce the total operator and carrier machine vibration exposure.
Visit www.aimattachments.com or call (800) 789-8554 for more information.
FINTEC 542 TRACKED SCREEN
The Fintec 542 Tracked Screen is designed specifically for the recycling and contractor market.
• It has a 12-foot by 5-foot two bearing screenbox with increased screening angle built into the bottom deck of the screen. This feature coupled with the larger screening surface area and increased throw on the 
screenbox enhances screening efficiency and capacity, through the actual screenbox itself.
• The Fintec 542 Tracked Screen has a unique user-friendly folding access walkway fitted as standard around the screenbox, thus providing the operator with easy access for maintenance.
• Also, the belt feeder has an 8-cubic-meter capacity and is fitted with a radio controlled tipping reject grid as standard.
• It is driven by a Cat 3054C water-cooled diesel 99-hp engine with an Engine Shut Down Protection System.
Visit www.fintec.com for more information.
BOBCAT S100 SKID STEER
Bobcat Co. has introduced the S100 skid-steer loader, a compact loader with a 1,000-pound rated operating capacity. 
• The S100 has a spacious cab, easy-to-read instrument panel and transversely mounted engine in a frame small enough to access and work in some of the tightest areas.
• The S100 model replaces the Bobcat 553 skid steer model and isdesigned for customers in the rental, demolition, landscaping and construction markets. It has a width of 50 inches and allows operators to travel through backyard gates in residential areas, access the inside of buildings for interior demolition work and work between buildings and other tight quarters.
Visit www.bobcat.com for more information.
RED RHINO 7000 SERIES
The 7000 series is a dedicated secondary building and demolition rubble recycler.
• The machine has a jaw of 700 mm by 400 mm and an output of 20 mm
up to 140 mm.
• The 7000 includes a vibratory tray feeder with grizzly and is also fully remote controlled.
• It has an optional overband magnetic tramp removal system available.
• Powered by a 67-hp Deutz water cooled diesel engine.
Visit www.metabousa.com for more information.
ATLAS COPCO DIESEL HYDRAULIC POWER PACK
The LP 13-20 LED power pack is designed to place less load on the engine when working with demanding tools like heavier handheld hydraulic 
breakers and is built to withstand vibrations.
• The LP 13-20 DEL is powered by an air-cooled, 10-hp Lombardini series 15LD diesel engine, with recoil and electric start. Comparison tests with previous other power pack models have shown that the new engine is less loaded in demanding conditions, according to the manufacturer.
• The new pack offers hydraulic oil flow of 5.3 gallons per minute at a maximum pressure of 2,175 psi. The power pack has an oil capacity of 1.3 gallons.
• The LP 13-20 DEL is well suited for tunneling jobs and poorly ventilated areas as well as other applications where diesel is preferred.
• The 256-pound hydraulic power pack can efficiently power a wide assortment of handheld hydraulic tools and breakers for various construction, utility and demolition projects.
Visit www.atlascopco.com for more information.
Explore the September 2007 Issue
Check out more from this issue and find your next story to read.
Latest from Construction & Demolition Recycling
- Biden administration announces $2B in grants to improve airport infrastructure
- King County, Washington, reduces waste generated from building demolition
- Biffa adds C&D recycling firm to its portfolio
- Volvo CE marks 50 years of manufacturing in Pennsylvania
- Bomag names new VP of sales and marketing
- Silos in San Francisco eyed for demolition
- Rotochopper cuts ribbon on R&D facility
- Hendrickson expands Primaax Ex suspension offering
